"Elster" markasına ait modeller;
Flow meter For metering gas where no calibration is required, display of the quantity consumed, with E1 and E200 pulse generators Nominal flow rate: 250 m3/h, measuring range: 20-400 m3/h(b) Intermediate flange DN 80, E1: 1 pulse/m3, E200: 187.5 pulses/m3 pu max. 4 bar, for gas and air Stat. Warennummer 90281000
QA 250Z800-40

Elster
Flow meter For metering gas where no calibration is required, display of the quantity consumed, with E1 and E200 pulse generators Nominal flow rate: 250 m3/h, measuring range: 20-400 m3/h(b) Intermediate flange DN 80, E1: 1 pulse/m3, E200: 187.5 pulses/m3 pu max. 4 bar, for gas and air Stat. Warennummer 90281000
Flow meter For non-calibration Gas quantity metering, display of consumed Quantity, with pulse generators E1 and E200 Nominal flow: 65 m3/h, measuring range 6-100 m3/h(b) Intermediate flange DN 50, E1: 1 Imp/m3, E200: 250 Imp/m3 pu max. 4 bar, for gas and air QA65Z50-40 Flow meter For metering gas where no calibration is required, display of the quantity consumed, with E1 and E200 pulse generators Nominal flow rate: 65 m3/h, measuring range: 6-100 m3/h(b) Intermediate flange DN 50, E1: 1 pulse/m3, E200: 250 pulses/m3 pu max. 4 bar, for gas and air
QA 65Z50-40

Elster
Flow meter For non-calibration Gas quantity metering, display of consumed Quantity, with pulse generators E1 and E200 Nominal flow: 65 m3/h, measuring range 6-100 m3/h(b) Intermediate flange DN 50, E1: 1 Imp/m3, E200: 250 Imp/m3 pu max. 4 bar, for gas and air QA65Z50-40 Flow meter For metering gas where no calibration is required, display of the quantity consumed, with E1 and E200 pulse generators Nominal flow rate: 65 m3/h, measuring range: 6-100 m3/h(b) Intermediate flange DN 50, E1: 1 pulse/m3, E200: 250 pulses/m3 pu max. 4 bar, for gas and air
Flow meter For non-calibration Gas quantity metering, display of consumed Quantity, with pulse generators E1 and E200 Nominal flow: 250 m3/h, measuring range 20-400 m3/h(b) Intermediate flange DN 100, E1: 1 Imp/m3, E200: 187.5 Imp/m3 pu max. 4 bar, for gas and air QA250Z100-40 Flow meter For metering gas where no calibration is required, display of the quantity consumed, with E1 and E200 pulse generators Nominal flow rate: 250 m3/h, measuring range: 20-400 m3/h(b) Intermediate flange DN 100, E1: 1 pulse/m3, E200: 187.5 pulses/m3 pu max. 4 bar, for gas and air
QA 250Z100-40

Elster
Flow meter For non-calibration Gas quantity metering, display of consumed Quantity, with pulse generators E1 and E200 Nominal flow: 250 m3/h, measuring range 20-400 m3/h(b) Intermediate flange DN 100, E1: 1 Imp/m3, E200: 187.5 Imp/m3 pu max. 4 bar, for gas and air QA250Z100-40 Flow meter For metering gas where no calibration is required, display of the quantity consumed, with E1 and E200 pulse generators Nominal flow rate: 250 m3/h, measuring range: 20-400 m3/h(b) Intermediate flange DN 100, E1: 1 pulse/m3, E200: 187.5 pulses/m3 pu max. 4 bar, for gas and air
Flow meter For non-calibrated Gas quantity metering, display of the consumed Quantity, with pulse generators E1 and E200 Nominal flow rate: 65 m³/h Measuring range 6-100 m3/h(b) intermediate flange DN 50, E1: 1 Imp/m3, E200: 250 Imp/m3 PU max. 4 bar, for gas and air
QA 65Z50-40

Elster
Flow meter For non-calibrated Gas quantity metering, display of the consumed Quantity, with pulse generators E1 and E200 Nominal flow rate: 65 m³/h Measuring range 6-100 m3/h(b) intermediate flange DN 50, E1: 1 Imp/m3, E200: 250 Imp/m3 PU max. 4 bar, for gas and air
FI - Flow Indicator, P Max: 18.8 Bar, QMIN: 800 M3/H, QMAX: 16000M3/H, Grate: 10000
SM-RI-X-L

Elster
FI - Flow Indicator, P Max: 18.8 Bar, QMIN: 800 M3/H, QMAX: 16000M3/H, Grate: 10000
BCU 570WC1F1U0K1-E Burner control unit Housing for control cabinet installation, for controlling, igniting and monitoring modulating forced draught burners. For continuous operation with ionization control or UV control using UV sensor UVD. Intermittent operation with UV sensor UVS. Display of the program status, unit parameters and flame signal. Manual operating mode. Diagnosis and adjustment of unit parameters via optical interface using PC software BCSoft. Series: 570 Market: EU certified, certified for systems up to SIL 3 (compliant with PL e) Mains voltage: 230 V~, 50/60 Hz Valve proving system: Yes Capacity control: Modulating capacity control with interface for actuator IC Flame control: With ionization or UV signal Electrical connection: Screw connection terminals Individual packaging: Yes 04 Flame control: Ionization 01 Burner switch-off threshold: 5 micro A 07 Burner start-up attempts: 1 09 Restart: No 10 Emergency stop: With fault lock-out 12 High gas pressure protection: With fault lock-out 13 Low pressure cut-off: With fault lock-out 15 Air deficiency cut-out: With fault lock-out 19 Safety time during operation: 1 s 40 Capacity control: With IC 20 30 Fan run-up time tGV: 0 s 32 Air flow monitoring during controlled air flow: Off; controller enable 33 Start-up with pre-purge: Yes (depending on P34 Pre-purge time tPV) 34 Pre-purge time tPV: 6000 s 35 Air flow monitoring during pre-purge: With fault lock-out 37 Post-purge time tPN: 6000 s 38 Air flow monitoring during post-purge: Off; control element to maximum capacity 44 Controller enable signal delay time tRF: 0 s 61 Minimum burner on time tB: 0 s 62 Minimum pause time tBP: 0 s 63 Switch-on delay time tE: 0 s 67 Operating time in Manual mode limited to 5 min.: Yes 77 User-defined password: ---- 78 Burner application: Burner with pilot gas and pilot burner 79 Pilot burner: With shut-down 80 Fieldbus communication: With address check 93 Pre-ignition time tVZ: 1 s 94 1st safety time on start-up: 3 s 95 Flame proving period 1 tFS1: 2 s 96 2nd safety time on start-up: 5 s 97 Flame proving period 2 tFS2: 2 s
BCU 570WC1F1U0K1-E

Elster
BCU 570WC1F1U0K1-E Burner control unit Housing for control cabinet installation, for controlling, igniting and monitoring modulating forced draught burners. For continuous operation with ionization control or UV control using UV sensor UVD. Intermittent operation with UV sensor UVS. Display of the program status, unit parameters and flame signal. Manual operating mode. Diagnosis and adjustment of unit parameters via optical interface using PC software BCSoft. Series: 570 Market: EU certified, certified for systems up to SIL 3 (compliant with PL e) Mains voltage: 230 V~, 50/60 Hz Valve proving system: Yes Capacity control: Modulating capacity control with interface for actuator IC Flame control: With ionization or UV signal Electrical connection: Screw connection terminals Individual packaging: Yes 04 Flame control: Ionization 01 Burner switch-off threshold: 5 micro A 07 Burner start-up attempts: 1 09 Restart: No 10 Emergency stop: With fault lock-out 12 High gas pressure protection: With fault lock-out 13 Low pressure cut-off: With fault lock-out 15 Air deficiency cut-out: With fault lock-out 19 Safety time during operation: 1 s 40 Capacity control: With IC 20 30 Fan run-up time tGV: 0 s 32 Air flow monitoring during controlled air flow: Off; controller enable 33 Start-up with pre-purge: Yes (depending on P34 Pre-purge time tPV) 34 Pre-purge time tPV: 6000 s 35 Air flow monitoring during pre-purge: With fault lock-out 37 Post-purge time tPN: 6000 s 38 Air flow monitoring during post-purge: Off; control element to maximum capacity 44 Controller enable signal delay time tRF: 0 s 61 Minimum burner on time tB: 0 s 62 Minimum pause time tBP: 0 s 63 Switch-on delay time tE: 0 s 67 Operating time in Manual mode limited to 5 min.: Yes 77 User-defined password: ---- 78 Burner application: Burner with pilot gas and pilot burner 79 Pilot burner: With shut-down 80 Fieldbus communication: With address check 93 Pre-ignition time tVZ: 1 s 94 1st safety time on start-up: 3 s 95 Flame proving period 1 tFS1: 2 s 96 2nd safety time on start-up: 5 s 97 Flame proving period 2 tFS2: 2 s
86048010 gas pressure regulator Spring-loaded, with pre-pressure compensation membrane and zero degree, for Keeping the adjustable pressure constant DN 50 Flange according to ISO 7005 PU max. 4 bar Locking screw in the input and output For gas, EC type tested and certified Set to 20 mbar (range 10-30 mbar)
VGBF 50F40-3

Elster
86048010 gas pressure regulator Spring-loaded, with pre-pressure compensation membrane and zero degree, for Keeping the adjustable pressure constant DN 50 Flange according to ISO 7005 PU max. 4 bar Locking screw in the input and output For gas, EC type tested and certified Set to 20 mbar (range 10-30 mbar)
84315200 UV probe For monitoring gas burners in intermittent operation, EC type tested and certified in conjunction with Elster Kromschröder automatic gas burners Series 10 Thermal protection made of quartz glass Rp 1/2 internal thread M20 screw connection
UVS 10D0G1

Elster
84315200 UV probe For monitoring gas burners in intermittent operation, EC type tested and certified in conjunction with Elster Kromschröder automatic gas burners Series 10 Thermal protection made of quartz glass Rp 1/2 internal thread M20 screw connection
47545022 Gas pressure regulator with safety diaphragm default setting pd 80 mbar pso180 mbar HTB version, with flange connection DN 50, PN 16 Overall length: 220 mm HTB - execution Inlet pressure Pe max. 1 bar with built-in SAV
MR50 F, PN 1 SM

Elster
47545022 Gas pressure regulator with safety diaphragm default setting pd 80 mbar pso180 mbar HTB version, with flange connection DN 50, PN 16 Overall length: 220 mm HTB - execution Inlet pressure Pe max. 1 bar with built-in SAV
47124010 Flow meter with electronical counter head For metering gas where no calibration is required, display of the quantity consumed, key-date value, key date, current flow rate and high resolution of the quantity consumed, with E200 pulse generator. Nominal flow rate: 400 m3/h, measuring range: 32-650 m3/h(b) Intermediate flange DN 100, E200: 187.5 pulses/m3 pu max. 4 bar, for gas and air M-Bus interface
QAe 400Z100-40

Elster
47124010 Flow meter with electronical counter head For metering gas where no calibration is required, display of the quantity consumed, key-date value, key date, current flow rate and high resolution of the quantity consumed, with E200 pulse generator. Nominal flow rate: 400 m3/h, measuring range: 32-650 m3/h(b) Intermediate flange DN 100, E200: 187.5 pulses/m3 pu max. 4 bar, for gas and air M-Bus interface
47121680 Flow meter with electronical counter head For metering gas where no calibration is required, display of the quantity consumed, key-date value, key date, current flow rate and high resolution of the quantity consumed, with E200 pulse generator Nominal flow rate: 160 m3/h, measuring range: 13-250 m3/h(b) Intermediate flange DN 80, E200: 187.5 pulses/m3 pu max. 4 bar, for gas and air M-Bus interface
QAe 160Z80-40

Elster
47121680 Flow meter with electronical counter head For metering gas where no calibration is required, display of the quantity consumed, key-date value, key date, current flow rate and high resolution of the quantity consumed, with E200 pulse generator Nominal flow rate: 160 m3/h, measuring range: 13-250 m3/h(b) Intermediate flange DN 80, E200: 187.5 pulses/m3 pu max. 4 bar, for gas and air M-Bus interface
47104025 Flow meter For metering gas where no calibration is required, display of the quantity consumed, with E1 and E200 pulse generators Nominal flow rate: 40 m3/h, measuring range: 3.3-65 m3/h(b), Rp internal thread, DN 25, E1: 10 pulses/m3, E200: 500 pulses/m3 pu max. 4 bar, for gas and air
QA 40R25-40

Elster
47104025 Flow meter For metering gas where no calibration is required, display of the quantity consumed, with E1 and E200 pulse generators Nominal flow rate: 40 m3/h, measuring range: 3.3-65 m3/h(b), Rp internal thread, DN 25, E1: 10 pulses/m3, E200: 500 pulses/m3 pu max. 4 bar, for gas and air
47102525 Flow meter For metering gas where no calibration is required, display of the quantity consumed, with E1 and E200 pulse generators Nominal flow rate: 25 m3/h, measuring range: 2.5-40 m3/h(b) Rp internal thread DN 25, E1: 10 pulses/m3, E200: 500 pulses/m3 pu max. 4 bar, for gas and air
QA 25R25-40

Elster
47102525 Flow meter For metering gas where no calibration is required, display of the quantity consumed, with E1 and E200 pulse generators Nominal flow rate: 25 m3/h, measuring range: 2.5-40 m3/h(b) Rp internal thread DN 25, E1: 10 pulses/m3, E200: 500 pulses/m3 pu max. 4 bar, for gas and air
(factory test / calibration)
Testing costs TRZ DN 150 to 250

Elster
(factory test / calibration)
(factory inspection / calibration) including low-pressure test for an operating pressure of 0 to 4 barg test medium: air
Prüfkosten TRZ DN 80+100

Elster
(factory inspection / calibration) including low-pressure test for an operating pressure of 0 to 4 barg test medium: air
AS1440-W32C-441-OSE-1A37S-BDB00

Elster
METER NATURAL GAS DN150 PN20 ELSTER G650 H

Elster
Q400 DN150 PN10

Elster
AS3000, 100A directly connected, 230/400V,

Elster
Turbine gas meter calibrated

Elster