Kategoriler
Wiper, Nitrile Rubber
Oteco - 22" x 3 1/2" Double Split Rap-A-Round Pipe

Wiper, Nitrile Rubber
Welded construction in square or rectangular design Flanges acc. to ORBINOX-Standard Size : W x H = 250 x 250 mm Body : Stainless Steel AISI 316 (1.4401) Corrosion Protection : --- (not required) Slide : Stainless Steel AISI 316 (1.4401) Yoke : Steel, epoxycoated Gland Follower : Stainless Steel AISI 316 (1.4401) Seat : Silicone Packing : PTFE-impreg. Synthetikfibre (Type ST) Actuator : pneumatic cylinder Approved Mediumcolumn : 1 kg/cm2 Accessories : - Without Flangesealing- and Fixingmaterial
Orbinox - Square Port Knife Gate Valve 250 x 250 mm

Welded construction in square or rectangular design Flanges acc. to ORBINOX-Standard Size : W x H = 250 x 250 mm Body : Stainless Steel AISI 316 (1.4401) Corrosion Protection : --- (not required) Slide : Stainless Steel AISI 316 (1.4401) Yoke : Steel, epoxycoated Gland Follower : Stainless Steel AISI 316 (1.4401) Seat : Silicone Packing : PTFE-impreg. Synthetikfibre (Type ST) Actuator : pneumatic cylinder Approved Mediumcolumn : 1 kg/cm2 Accessories : - Without Flangesealing- and Fixingmaterial
Wafer type gate valve in short overall length, sealing on one side, for installation between flanges according to EN 1092-2 PN 10 Nominal width : DN 80 Housing : stainless steel CF8M (1.4408) Knife : AISI 316 (1.4401) stainless steel Piston rod : stainless steel AISI 430 (1.4016) Mounting bracket : steel, epoxy-coated prepared for 2 roller limit switches (open/close) Protection against accidental contact : stainless steel AISI 304 (1.4301) Gland follower : stainless steel CF8M (1.4408) Gland packing : PTFE-impregnated synthetic fiber (Type ST) Sealing ring : EPDM Sealing clamp ring : Type A (standard), stainless steel AISI 316 (1.4401) Actuation : aluminum double-acting pneumatic actuator Control pressure : 5 – 7 bar permissible differential pressure in flow direction: DN 50 to 250 = 10 bar, DN 300 to DN 400 = 6 bar DN 450 = 5 bar, DN 500 to DN 600 = 4 bar Accesories : - Without flange seal and fastening material
Orbinox - Typ EX-N

Wafer type gate valve in short overall length, sealing on one side, for installation between flanges according to EN 1092-2 PN 10 Nominal width : DN 80 Housing : stainless steel CF8M (1.4408) Knife : AISI 316 (1.4401) stainless steel Piston rod : stainless steel AISI 430 (1.4016) Mounting bracket : steel, epoxy-coated prepared for 2 roller limit switches (open/close) Protection against accidental contact : stainless steel AISI 304 (1.4301) Gland follower : stainless steel CF8M (1.4408) Gland packing : PTFE-impregnated synthetic fiber (Type ST) Sealing ring : EPDM Sealing clamp ring : Type A (standard), stainless steel AISI 316 (1.4401) Actuation : aluminum double-acting pneumatic actuator Control pressure : 5 – 7 bar permissible differential pressure in flow direction: DN 50 to 250 = 10 bar, DN 300 to DN 400 = 6 bar DN 450 = 5 bar, DN 500 to DN 600 = 4 bar Accesories : - Without flange seal and fastening material
Wafer type gate valve in short overall length, sealing on one side, for installation between flanges according to EN 1092-2 PN 10 Nominal width : DN 100 Housing : GJL 250/GG 25, epoxy coated RAL 5015 Knife : AISI 304 (1.4301) stainless steel Piston rod : stainless steel AISI 430 (1.4016) Mounting bracket : steel, epoxy coated Protection against accidental contact : stainless steel AISI 304 (1.4301) Gland follower: up to DN 300 aluminum, from DN 350 ductile iron Gland packing : PTFE-impregnated synthetic fiber (type ST) with EPDM O-ring Sealing ring : EPDM Sealing clamp ring : Type A (standard), stainless steel AISI 304 (1.4301) Actuation : aluminum double-acting pneumatic actuator Control pressure : 5 – 7 bar permissible differential pressure in flow direction: DN 50 to 250 = 10 bar, DN 300 to DN 400 = 6 bar DN 450 = 5 bar, DN 500 to DN 600 = 4 bar DN 700 to DN 1200 = 2 bar Accesories : - - - Without flange seal and fastening material
Orbinox - Knife gate valve type EXN

Wafer type gate valve in short overall length, sealing on one side, for installation between flanges according to EN 1092-2 PN 10 Nominal width : DN 100 Housing : GJL 250/GG 25, epoxy coated RAL 5015 Knife : AISI 304 (1.4301) stainless steel Piston rod : stainless steel AISI 430 (1.4016) Mounting bracket : steel, epoxy coated Protection against accidental contact : stainless steel AISI 304 (1.4301) Gland follower: up to DN 300 aluminum, from DN 350 ductile iron Gland packing : PTFE-impregnated synthetic fiber (type ST) with EPDM O-ring Sealing ring : EPDM Sealing clamp ring : Type A (standard), stainless steel AISI 304 (1.4301) Actuation : aluminum double-acting pneumatic actuator Control pressure : 5 – 7 bar permissible differential pressure in flow direction: DN 50 to 250 = 10 bar, DN 300 to DN 400 = 6 bar DN 450 = 5 bar, DN 500 to DN 600 = 4 bar DN 700 to DN 1200 = 2 bar Accesories : - - - Without flange seal and fastening material
Vortex Model No. GRA350-F-AP-S4-MG-PET, 350MM Quantum Series Orifice Gate Valve. Aluminum valve body with live loaded, wear compensating seals, a 304 stainless steel blade, main flange and orifice liners. Material contact is 304 stainless steel and polymer. ͻOversized double acting air cylinder actuator ͻ(AP) - Inlet and Outlet Flanges match #125/150 ANSI mounting pattern. Flanges are aluminum to prevent corrosion due to oxidation and have blind tapped steel thread inserts for bolted customer connection. Caution: Using a bolt longer than the specified maximum will result in damage to the gate valve. Consult IOM manual for correct bolt length. ͻ(MG) - Air cylinder is equipped with a magno-piston for use with magnetic reed position indication switches. ͻ(PET) - Valve is rated for 180F(82C) maximum continuous service. PET pressure plates are backed with a foam void filler and live loaded natural rubber load seals. ͻValve has boss welded into main body to accept proximity switches. **OPTIONAL ACCESSORIES**
Vortex - GRA350-F-AP-S4-MG-PET

Vortex Model No. GRA350-F-AP-S4-MG-PET, 350MM Quantum Series Orifice Gate Valve. Aluminum valve body with live loaded, wear compensating seals, a 304 stainless steel blade, main flange and orifice liners. Material contact is 304 stainless steel and polymer. ͻOversized double acting air cylinder actuator ͻ(AP) - Inlet and Outlet Flanges match #125/150 ANSI mounting pattern. Flanges are aluminum to prevent corrosion due to oxidation and have blind tapped steel thread inserts for bolted customer connection. Caution: Using a bolt longer than the specified maximum will result in damage to the gate valve. Consult IOM manual for correct bolt length. ͻ(MG) - Air cylinder is equipped with a magno-piston for use with magnetic reed position indication switches. ͻ(PET) - Valve is rated for 180F(82C) maximum continuous service. PET pressure plates are backed with a foam void filler and live loaded natural rubber load seals. ͻValve has boss welded into main body to accept proximity switches. **OPTIONAL ACCESSORIES**
Vertex degaussing device 230V
Vertex - VDM-9

Vertex degaussing device 230V
VALVE,GATE:KNIFE,6IN,CLASS 150,CI ASTM HANDWHEEL, CAST IRON ASTM A126 Body, 316SS STEM, NITRILE SEAT
Orbinox - 36085956

VALVE,GATE:KNIFE,6IN,CLASS 150,CI ASTM HANDWHEEL, CAST IRON ASTM A126 Body, 316SS STEM, NITRILE SEAT
UPPER DIAPHRAGM PROTECTOR MODEL-7
Oteco - 397008

UPPER DIAPHRAGM PROTECTOR MODEL-7
uni-directional wafertype knife gate valve, Flanges acc. to EN 1092-2 PN 10 Diameter : DN 80 Body : Stainless steel CF8M (1.4408) Slide : Stainless steel AISI 316 (1.4401) Stem : Stainless Steel AISI 430 (1.4016) , rising Yoke : Steel, Epoxycoated Gland follower : Stainless steel CF8M (1.4408) Packing : Graphite (Type GR) Seat : metal Seat retainer ring : - - - Actuator : Handwheel Max. pressure in flowdirection : DN 50 to 250 = 10 bar, DN 300 to DN 400 = 6 bar DN 450 = 5 bar, DN 500 to DN 600 = 4 bar without Flangesealing- und Fixingmaterial
Orbinox - ORBINOX-Knifegatevalve Type EXV DN 80

uni-directional wafertype knife gate valve, Flanges acc. to EN 1092-2 PN 10 Diameter : DN 80 Body : Stainless steel CF8M (1.4408) Slide : Stainless steel AISI 316 (1.4401) Stem : Stainless Steel AISI 430 (1.4016) , rising Yoke : Steel, Epoxycoated Gland follower : Stainless steel CF8M (1.4408) Packing : Graphite (Type GR) Seat : metal Seat retainer ring : - - - Actuator : Handwheel Max. pressure in flowdirection : DN 50 to 250 = 10 bar, DN 300 to DN 400 = 6 bar DN 450 = 5 bar, DN 500 to DN 600 = 4 bar without Flangesealing- und Fixingmaterial
Type: Hipex-24-11-AL-E Connection: IN & OUT 1-1/2" NPT Pilot 1/4" NPT Material: SS316 Operating temperature range: -60°C to +40°C CV: 35 HIPEX 2-way quick air vent 24 1-1/2" NPT ports 11Ratio 1:1 AL seals in fluorosilicone E 1 x exhaust air connection
Bifold - [11179] 1 1/2" HIPEX - Bifold 24

Type: Hipex-24-11-AL-E Connection: IN & OUT 1-1/2" NPT Pilot 1/4" NPT Material: SS316 Operating temperature range: -60°C to +40°C CV: 35 HIPEX 2-way quick air vent 24 1-1/2" NPT ports 11Ratio 1:1 AL seals in fluorosilicone E 1 x exhaust air connection
Type: FP10P-S1-04-32-NU-AL-77G-24D-57 Material: SS316L Operating pressure: 0-10 bar(g) Operating temperature range: -55°C to +40°C (@T6) CV: 1 FP10P Standard Service (direct acting) S1 actuator: solenoid coil 04 1/4" NPT-F connections 32 3 ways, 2 positions NU Normally Universal (1->2 = NC / 3 ->2 = NO) AL Fluorosilicone seals (-55°C to +130°C) 77G Protection class: CU-TR/IECEx, Ex d IIC, Ex tb IIIC Db T4/5/6 24D power supply 24V DC 57 Power consumption 5.7 watts
Bifold - [3389] 1/4" NPT - MV - Bifold - FP10P - 77G

Type: FP10P-S1-04-32-NU-AL-77G-24D-57 Material: SS316L Operating pressure: 0-10 bar(g) Operating temperature range: -55°C to +40°C (@T6) CV: 1 FP10P Standard Service (direct acting) S1 actuator: solenoid coil 04 1/4" NPT-F connections 32 3 ways, 2 positions NU Normally Universal (1->2 = NC / 3 ->2 = NO) AL Fluorosilicone seals (-55°C to +130°C) 77G Protection class: CU-TR/IECEx, Ex d IIC, Ex tb IIIC Db T4/5/6 24D power supply 24V DC 57 Power consumption 5.7 watts
SUB GASKET MODEL-7
Oteco - 397062

SUB GASKET MODEL-7